Oilfield Innovations' patented Multi-Production-Injection-Crossover (MPIX) combined with conventional multi-lateral and extended reach drilling (ERD) technologies can provide multi-stage fracks in opposite directions to double production from a single well bore or access two different reservoirs between one (1) and two (2) kilometres apart, as shown to the left.
Fracks can extend in opposite to double the shale accessed by a single well bore or both reservoirs can be connected into the same subsea tie-back or platform slot to provide 2-for-1 well costs by sharing the same production casing.
Regardless of whether your wells are onshore or offshore Oilfield Innovations' MPIX tool can give you two wells for the cost of one.
Oilfield Innovations' patented tool can control two (2) differently pressured production flow streams to, for example, produce a lower pressure reservoir above a higher pressure deeper reservoir.
Our Multi-Production-Injection-Crossover (MPIX) can also produce a gas cap and oil rim through the same production casing, as shown to the right.
Our MPIX tool can also produce from different compartments of the same reservoir that can depleted and different rates and, thus, require separate flow streams to prevent cross flow.
Oilfield Innovations' patented MPIX tool can also be used in huff-and-puff cyclical production and injection in different layered formations, dispose of produced water to provide water drive pressure support or for gas injection for gas cap drive support.
For stranded hydrocarbons without the ability to flare oil associated gases, our MPIX tool can also be used to re-inject gas into a gas cap or as a gas flood or gas sweep drive system.
Injecting chemicals, gases or fluids into the same well being produced can enhance recovery significantly at minimal cost.
Oilfield Innovations' Multi-Production-Injection-Crossover (MPIX) can be used to disposed of produced water and carry out water, steam or gas floods or sweeps for enhanced production and recovery.
Whether the wells are offshore where space is expensive or onshore where minimising ground water penetrations and gathering facility foot prints is equally important, Oilfield Innovations' patented MPIX tool can reduce cost and/or increase production.
Can you afford to ignore new technology that is a simple crossover with no moving parts that can turn every well you drill into two (2) wells?
Disclaimers: Oilfield Innovations Limited (OILtd) does not promise that the site or any content, service or feature of the site or new technology will be error-free or that any defects will be corrected, or that your use of the site or technology will provide specific results. The site and its content are delivered on an “as-is” and “as-available” basis. All information provided on the site is subject to change without notice. OILtd cannot ensure that any files or other data you download from the site will be free of viruses or contamination or destructive features. OILtd disclaims all warranties, express or implied, including any warranties of accuracy, non-infringement, merchantability and fitness for a particular purpose. OILtd disclaims any and all liability for the acts, omissions and conduct of any third parties in connection with or related to your use of the site and/or any OILtd technologies or services. You assume total responsibility for your use of the site and any linked sites or new technologies. Your sole remedy against OILtd for dissatisfaction with the site or any content is to stop using the site or any such content or technology. This limitation of relief is a part of the bargain between the parties. The above disclaimer applies to any damages, liability or injuries caused by any failure of performance, error, omission, interruption, deletion, defect, delay in operation or transmission, computer virus, communication line failure, theft or destruction of or unauthorized access to, alteration of, or use, whether for breach of contract, tort, negligence or any other cause of action. OILtd reserves the right to do any of the following, at any time, without notice: (1) to modify, suspend or terminate operation of or access to the Site, or any portion of the Site, for any reason; (2) to modify or change the Site, or any portion of the Site, and any applicable policies or terms; and (3) to interrupt the operation of the Site, or any portion of the Site, as necessary to perform routine or non-routine maintenance, error correction, or other changes.